chartinael
09.03.2005, 22:40
Diesen und weitere DIY Threads können hier eingesehen werden:
DIY Threads auf Eurostylez.Org (http://eurostylez.watt-is-dingens.de/homepage/forum2/board.php?boardid=22)
Installation einer dritten Bremsleuchte für den EK9 Wing.
Materialien:
- LOGO Bremslicht
- Dremel
- schwarzes Silikon
- 2 Schneidschrauben
Entlang der roten Linien muß die Leuchte mit einem Dremel gekürzt werden.
Seitenansicht:
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/change-side.jpg
Vorderansicht:
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/change-front.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/cut-out1.jpg
Rückansicht:
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/change-back.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/cut-out2.jpg
Dann Cover auf Leuchte stecken und Hatch-Decken-Paneel auflegen. Ein Loch für die Kabeldurchführung "schmelzen" und 2 für die Verschraubung. Diese genau durch die Seitenklipse bohren und nicht in die Leuchte direkt.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/oben.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/unten.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/vorne.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/rear.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/seite.jpg
Den Überganz von Paneel zur Leuchte mit Silikon abdichten.
An das Kabelende die Kabel der Originalspoiler Bremsleuchte anklemmen.
Nun nimmt man die vorbereitete Leuchte mit zum Auto und macht sich an den Einbau.
Man zieht einen Draht von der Seite zu dem runden Auslaß, um damit die Kabel durchzuziehen.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/wire.jpg
Dann hab ich den Draht in den Stecker-Prong reingesteckt ... das war ausreichend fest, daß man das dann durch den Rahmen ziehen konnte.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/pull-preparation.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/pull.jpg
Dann zieht man beide Kabel durch die Öffung und steckt die Prongs in den Connector.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/prongs.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/connector.jpg
Dann verbindet man die beiden Gegenstücke und steckt sie in den Rahmen rein und macht die Grommit wieder rein.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/grommit.jpg
Dann macht man die Leuchte wieder ran, indem man das Paneel ganz normal wieder ranpappt.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-hatch1.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-aussenansicht1.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-aussenansicht.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-innenansicht.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed1.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed2.jpg
Ja, so sieht das mit dem Logo-Licht von Stanley mit E-Kennzeichen aus.
Hab übrigens noch ein Extra Licht vom Logo. Falls jemand an einem Nachbau Interesse hat.
DIY Threads auf Eurostylez.Org (http://eurostylez.watt-is-dingens.de/homepage/forum2/board.php?boardid=22)
Installation einer dritten Bremsleuchte für den EK9 Wing.
Materialien:
- LOGO Bremslicht
- Dremel
- schwarzes Silikon
- 2 Schneidschrauben
Entlang der roten Linien muß die Leuchte mit einem Dremel gekürzt werden.
Seitenansicht:
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/change-side.jpg
Vorderansicht:
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/change-front.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/cut-out1.jpg
Rückansicht:
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/change-back.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/cut-out2.jpg
Dann Cover auf Leuchte stecken und Hatch-Decken-Paneel auflegen. Ein Loch für die Kabeldurchführung "schmelzen" und 2 für die Verschraubung. Diese genau durch die Seitenklipse bohren und nicht in die Leuchte direkt.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/oben.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/unten.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/vorne.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/rear.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/seite.jpg
Den Überganz von Paneel zur Leuchte mit Silikon abdichten.
An das Kabelende die Kabel der Originalspoiler Bremsleuchte anklemmen.
Nun nimmt man die vorbereitete Leuchte mit zum Auto und macht sich an den Einbau.
Man zieht einen Draht von der Seite zu dem runden Auslaß, um damit die Kabel durchzuziehen.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/wire.jpg
Dann hab ich den Draht in den Stecker-Prong reingesteckt ... das war ausreichend fest, daß man das dann durch den Rahmen ziehen konnte.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/pull-preparation.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/pull.jpg
Dann zieht man beide Kabel durch die Öffung und steckt die Prongs in den Connector.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/prongs.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/connector.jpg
Dann verbindet man die beiden Gegenstücke und steckt sie in den Rahmen rein und macht die Grommit wieder rein.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/grommit.jpg
Dann macht man die Leuchte wieder ran, indem man das Paneel ganz normal wieder ranpappt.
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-hatch1.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-aussenansicht1.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-aussenansicht.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed-innenansicht.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed1.jpg
http://eurostylez.watt-is-dingens.de/storage/diy/civic-brakelight/installed2.jpg
Ja, so sieht das mit dem Logo-Licht von Stanley mit E-Kennzeichen aus.
Hab übrigens noch ein Extra Licht vom Logo. Falls jemand an einem Nachbau Interesse hat.