PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : HONDATA Sammelbestellung



B_18-Turbo/Marian
27.05.2006, 05:06
Hi zuammen,
bin grad dabei Hondatas zu bestellen und zwar das S300.
http://www.bilder-hosting.de/img/CWP8H.jpg (http://www.bilder-hosting.de/show/CWP8H.html)
Preis: 460€ incl. Versand
natürlich nagelneu und unbenutzt...
Hat alle Funktionen des S200 und kommt serie schon mit 3 Step,Datalogging und Boost Option.
Is aber auch für Sauger geeignet!!!
Ist nich mehr wie das S100/200 eine kleine Box sondern passt ins ECU als extra Platine...
Hier der Auszug von Hondata:
s300/s300j Overview

The s300 is a plug in module to the factory Honda Engine Computer (ECU) which vastly expands the capabilities of the factory ECU. Forced induction, datalogging, real time updating of parameters, engine protection are but a few of the s300 features.



s300/s300j Pricing and Options

Price Description
$595 s300/s300j with all features and software

Features

Main features:

Fits inside the ECU
Built on the proven s100/s200 code base
USB connection for speed and compatibility
SManager Windows based software for parameter & table editing, calibration uploading and datalogging.
Real-time updating of ECU
Built in calibrations for common engine combinations
Built in datalogging to a laptop
On board datalogging memory (2 MB memory, 20-60 minutes datalogging)
Adjustment for different sized injectors, with overall fuel trim.
Configurable for any MAP sensor (to at 5 Bar and above)
TPS based table lookup for ITBs
Engine protection from over boost.
Expanded fuel and ignition tables, both in rpm and load, to 60 lbs boost and 11,000 rpm (these are not the upper limits)
Launch control with anti-lag
Full throttle shift
Two multi purpose outputs for nitrous control or similar
Lambda tracing (with a wideband o2 sensor)
SManager editing software features:

High and low speed 24 x 20 ignition and fuel tables for correct VTEC tuning
Injector size fuel trim
Fuel trim for starting, throttle tip in and individual cylinder trim
Rev limiter with fuel cut or fuel and ignition cut
Launch control with anti-lag
Full throttle shift
Adjustable VTEC window with load and throttle control
Secondary intake runner control
Adjustable idle speed
MAP sensor type and calibration
Adjustable boost cut with hot and cold settings
Shift light
Closed loop control
Air temperature compensation
Water temperature compensation
Fuel and ignition correction based on gear
A/C shutoff conditions
Closed loop
Two general purpose outputs for nitrous control, dual boost control or similar
On board datalogging trigger conditions
The s300 uses different connecting pins in the ECU from the s100/s200, and also has a slot cut in the side for the USB connector, so the ECU must be modified for use with the s300. The s300 is made to fit in a full frame ECU case (US and most markets), so will not fit in a JDM ECU case.

USB Connection

The s300 uses a high speed USB connection for both programming calibrations and datalogging. No more USB/serial connectors!

Real-time Update

The s300 can be updated in real-time with the engine running without affecting the operation of the vehicle. This means that calibrations and changes can be uploaded to the ECU very quickly (2 seconds for a new calibration, a fraction of a second for anything else), without interrupting the operation of the engine. Changes made in the SManager software are uploaded to the ECU instantly and you can see the effect immediately. The s300 does not use an EEPROM or equivalent, so you never need to open the ECU to change chips nor 'burn' ROMs. No EPROM programmer is necessary - you just need a laptop with USB port.

Datalogging

The s300 has datalogging to the SManager software built in via the USB port. Using a laptop the various ECU sensors can be datalogged, viewed, graphed and saved for later analysis.

Additionally the s300 has on board flash memory which allows a datalog recordings to be made without a laptop, for later access and download to a laptop. Multiple recordings can be made and stored in the s300 for a total of around 40 minutes of total datalogging time. An external switch can be used to start and stop recordings, or engine conditions can trigger recording. For instance in a drag race, the s300 can be set to start recording once the rpm is bought up to near launch rpm and automatically stop once past the traps and the rpm drops below a certain level.

MAP Sensor Compatibility

Any linear MAP sensor can be used, using a scalar and offset to translate the MAP sensor characteristics into pressure. Popular MAP sensor settings are built in for ease of setup. To do this you will need the map sensor calibration numbers from the manufacturer of the sensor.

ECU Preparation

Details on preparing the ECU can be found here. It is strongly recommended that you have this professionally installed as this is more difficult to install than an s200 and if the ecu has been previously socketed you run an even higher risk of damaging the ecu (lifting tracks and or burning them).

s300j Specific Notes

PCS output is not present on the JDM ECUs and cannot be used for nitrous controls. All other inputs and outputs are present and can be used for nitrous controls.



Bei Interesse einfach melden...

hociegb20ff
27.05.2006, 19:46
kannst du es auch abstimmen?

jdmking
27.05.2006, 19:57
Doppelcheck my son :lol: :lol: :D gayfight

B_18-Turbo/Marian
27.05.2006, 21:46
Ey Papa versau mir nicht den Thread sons gibbet ne Ohrlasche :mad:
gayfight :bussi:

Das abstimmen übernehme ich nicht nein.Keine Erfahrung mit Hondata.Da müssen Profis ran.Aber im Forum gibt es Leute wie EK4Turbo oder Ace die das im Schlaf können.Wende dich an sie.Sie sind sehr gut und günstig...

B_18-Turbo/Marian
28.05.2006, 22:33
Bestellung bitte bis zum 8.6.06 per pm an mich

Mitch
29.05.2006, 08:20
Mir wurde mal gesagt das Hondata hätte eine gangabhänige Ladedruckregelung. DIESES HIER hat das aber nicht oder?

B_18-Turbo/Marian
29.05.2006, 09:04
Ich meine man hat bei allen Hontadas Lastabhängige Regelungen.Aber ich bin nicht wirklich der ECU Fachmann und weiss nur übers Gröbste bescheid...Mach dich doch mal schlau bei Leuten die sich damit richtig auskennen.
PS: Hätts mich auch per ICE fragen können :P

VooDoo
29.05.2006, 09:18
Mir wurde mal gesagt das Hondata hätte eine gangabhänige Ladedruckregelung. DIESES HIER hat das aber nicht oder?

mir wäre neu das ein hondata überhaupt den ladedruck regeln kann.

B_18-Turbo/Marian
29.05.2006, 09:34
Er meint lastabhängige Ladedruckanpassung...Weiss nicht wie ich das besser ausdrücken soll...

hociegb20ff
29.05.2006, 10:36
fragt doch ace!der kann euch über hondata alles sagen!!!!

B_18-Turbo/Marian
29.05.2006, 10:43
Hab ich doch gesagt...Besser jemand fragen der sich damit auskennt

B_18-Turbo/Marian
29.05.2006, 11:36
@ Mitch

sorry mitch...hab dich wiedermal mit Matchi verwechselt :D

eg4
29.05.2006, 13:50
die honda ecus können keinen ladedruck regeln

B_18-Turbo/Marian
29.05.2006, 14:17
Sagt ja auch keiner. Einfach richtig lesen.Geht nur ums Lededruck/Benzinverhältnis das bei Last logischerweise ansteigt.Wie gesagt bin kein ECU Pro und weiss nicht wie ichs besser ausdrücken soll...